Advanced Wastewater Treatment Research Articles

Scattered and transmitted light as surrogates for activated carbon residual in advanced wastewater treatment processes: Investigating the influence of particle size

The use of powdered activated carbon (PAC) is a common process in advanced wastewater treatment to remove micropollutants. Retention and separation of PAC is essential as PAC loaded with micropollutants should not be released into the environment. Determining the activated carbon (AC) residual in the effluent poses a challenge, as there is currently no on-line measurement method. In this study, the correlation between turbidity, measured by scattered light, and absorption at wavelength of 550 nm (Absorption550 nm), measured by transmitted light, was investigated in relation to the AC residue. Linear correlations for turbidity (R2 = 0.95) and Absorption550 nm (R2 = 1.00) to AC concentrations were observed in both laboratory and full-scale experiments in a pilot plant where superfine PAC was added prior to Pile Cloth Media Filtration (PCMF). Decreasing the particle size (d50) while maintaining the same AC concentration leads to increased turbidity: Therefore, a fourfold reduction in d50 results in a 2- to 3-fold increase in turbidity, whereas a 30-fold reduction in d50 leads to a 6-to 8-fold increase. Furthermore, the original wastewater turbidity led to a parallel shift in the linear correlation between turbidity and AC. Coagulant doses of up to 400 mg Me3+/g AC resulted in a 50% reduction in turbidity. However, higher concentrations from 400 to 1,000 mg Me3+/g AC resulted in increased turbidity with only a 30% reduction compared to the initial turbidity. The study also highlights the significance of AC particle size in optical measurements, impacting result accuracy.

Pressure-driven membranes for advanced treatment of textile wastewater: Dye/salt fractionation, concentration, and cleaning strategies

Textile wastewater commonly contains various organic compounds and salt mixtures, potentially raising serious environmental and health concerns. Traditional treatment approaches are hindered by high salinity; consequently, membrane separation technologies have attracted increasing attention over the past few decades. Herein, four commercial pressure-driven membranes with molecular weight cut-off (MWCO) gradients were employed for the advanced treatment of different types of textile wastewater. Specifically, these membranes were initially subjected to a fractionation test toward the dye/salt mixtures, followed by deep concentration of the dye molecules. Using Congo red (CR), methyl blue (MB), NaCl, and Na2SO4 as representative dyes and salts, the results indicated that all membranes could effectively separate dye/salt mixtures and further conduct a deep concentration process toward the separated dye solutions. However, their efficiency and effectiveness largely depend on the membrane pore size and solution characteristics. For instance, membranes with lower MWCOs experience less fouling and shorter operation durations when treating CR-related solutions. All membranes showed improved fractionation efficiency toward MB/salt mixtures, requiring only approximately 10.2–42.9 % of the operation duration compared to CR-related solutions. The loose nanofiltration membrane proved superior to tight ultrafiltration membranes in both fractionation and concentration processes. Further research on cleaning methodologies demonstrated that both alkali and ethanol cleaning were influential in restoring the membrane performance. An appropriate ethanol/water concentration can effectively regenerate severely fouled membranes, achieving a high flux recovery ratio of ∼95 %. This study evaluated state-of-the-art pressure-driven membranes for textile wastewater treatment and guided cleaning strategies for optimal performance recovery.

Techno-economic feasibility of photovoltaic solar electrodialysis with bipolar membranes

Electrodialysis with bipolar membranes (EDBM) can transform desalination brines into acids and bases through the application of an electric field. Nevertheless, the widespread of EDBM is limited by its high energy consumption, typically based on fossil fuels. Yet, the integration of EDBM with renewable energy sources, like solar photovoltaic (PV), remains unexplored. This study presents a techno-economic analysis of PV-EDBM to produce NaOH and HCl from seawater reverse osmosis (SWRO) brines. An integrated PV-EDBM model was developed and applied to a hypothetical PV-EDBM plant located in the SWRO facility of Lampedusa (Italy). Results revealed that PV has no negative impact on the performance in terms of product concentration, specific energy consumption and current efficiency. Meanwhile, the levelized cost of NaOH for PV-EDBM was reduced by 20 % in comparison to the electrical grid mix, achieving 210 €·ton−1 NaOH on an annual average for PV-EDBM. Therefore, the investment associated with PV is offset by the benefits of reduced electricity costs from the grid. Consequently, EDBM emerges as a feasible solution to addressing resource scarcity, representing a significant step towards integrating renewable energies with advanced wastewater treatment technologies, thus paving the path to a greener future.

Suitability of treated wastewater for irrigation and its impact on groundwater resources in arid coastal regions: Insights for water resources sustainability

Water scarcity threatens agriculture and food security in arid regions like Saudi Arabia. The nation produces significant quantities of municipal wastewater, which, with adequate treatment, could serve as an alternative water source for irrigation, thereby reducing reliance on fossil and non-renewable groundwater. This study assessed the appropriateness of using treated wastewater (TWW) for irrigation in a dry coastal agricultural region in Eastern Saudi Arabia and its impact on groundwater resources. Field investigations were conducted in Qatif to collect water samples and field measurements. A multi-criteria approach was applied to evaluate the TWW's suitability for irrigation, including complying with Saudi Standards, the Irrigation Water Quality Index (IWQI), the National Sanitation Foundation water quality index (NSFWQI), and the individual irrigation indices. In addition, the impact of TWW on groundwater was assessed through hydrogeological and isotope approaches. The results indicate that the use of TWW in the study area complied with the Saudi reuse guidelines except for nitrate, aluminum, and molybdenum. However, irrigation water quality indices classify TWW as having limitations that necessitate the use for salt-tolerant crops on permeable and well-drained soils. Stable isotopic analysis (δ2H, δ18O) revealed that long-term irrigation with TWW affected the shallow aquifer, while deep aquifers were minimally impacted due to the presence of aquitard layer. The application of TWW irrigation has successfully maintained groundwater sustainability in the study area, as evidenced by increased groundwater levels up to 2.3 m. Although TWW contributes to crop productivity, long term agricultural sustainability could be enhanced by improving effluent quality, regulating irrigation practices, implementing buffer zones, and monitoring shallow groundwater. An integrated approach that combines advanced wastewater treatment methods, community involvement, regulatory oversight, and targeted monitoring is recommended to be implemented.

Investigation on pulsed-electrocoagulation process for the treatment of wet coffee processing wastewater using an aluminum electrode

The use of conventional direct current-electrocoagulation in wastewater treatment is limited by its drawbacks, which include electrode passivation, high energy consumption, and significant sludge generation. Therefore, to address these issues, pulsed-electrocoagulation (PECP) has been developed. The PECP is an advanced wastewater treatment technique that uses intermittent electrical pulses to target and break down organic compounds in wastewater. It offers several benefits, including enhanced removal of organic compounds, reduced chemical consumption, energy efficiency, treatment of complex wastewater composition, pathogen inactivation, environmental compliance, and potential for water reuse. In this research, removal efficiency of % Chemical Oxygen Demand (COD), % Color, % Turbidity, % phosphate, and %nitrate was investigated for the wet coffee processing wastewater by using PECP and the obtained results as the COD-98.75%, color-99.92%, turbidity-99.00%, phosphate-99.02%, and nitrate-98.83%, respectively. Independent variables were the major significant factors and the optimum value was investigated and obtained at pH of 7, electrolyte dosage of 0.75 g L−1, electrolysis time of 45 min, and current of 0.45 Amp. As a result, PECP with NaCl and CaCl2 as an electrolyte is an effective treatment technique for pollutant removal from wastewater. As a consequence, the specific benefits may vary depending on the system design, operational parameters, and wastewater characteristics. The pilot-scale studies and optimization are essential for assessing PECP feasibility and performance.

Synthesis of Integrated Material with Activation and Oxidation Functions by Mechanical Milling of Activated Carbon and Persulfate for Enhanced Tetracycline Degradation over Non-Radical Mechanism

As an alternative to the traditional advanced oxidation process of adding potassium persulfate (PS) and its activator to the solution separately, in this study, M(AC-PS), an integrated activator and catalyst, was synthesized by vacuum ball milling of PS and activated carbon (AC) to improve the PS’s utilization efficiency. The joint mechanical milling caused a change in the preferentially exposed crystal surface of the PS and the generation of more π-π* structures on the AC, leading to successful and stable connection of the PS onto the surface of the AC. Within 40 min, the M(AC-PS) achieved a degradation rate of 97.3% for tetracycline (TC, 20 mg/L), while the mixed system where AC and PS were separately ball milled achieved only a 53.1% removal of TC. Reactive oxygen species and electrochemical tests showed that M(AC-PS) mainly oxidized TC through non-free radical mechanisms. In M(AC-PS), AC provided oxygen-containing functional groups (e.g., C=O) to activate the PS and electron holes as an electron transfer medium, generating 1O2 and promoting electron donation from the TC to enhance the oxidation of the TC. Almost no catalytic components were detected in the solution, indicating that the obtained solid composite material avoids the limitations of solid–liquid interface contact and mass transfer, and then improves the efficiency of activation and catalysis. This study presents a simple and feasible method for obtaining efficient and convenient material for the advanced oxidation treatment of wastewater.

Activity and recyclability enhancement of pH-dependent Fe0@BC-mediated heterogeneous sodium percarbonate (SPC)-reducing agents (RA) system

Dyes pose great threats to the aquatic environment and human health. Fe0-based Fenton-like systems have been widely employed for the degradation of organic dyes. However, the regulation of degradability and recyclability was still unclear. In this study, Rhodamine B (RhB) was served as the model pollutant, hydroxylamine hydrochloride was selected as the RA, the natural photocatalysis system demonstrated stable operation. RA, as performance enhancement agent, was firstly reported in micro/nano-Zero-Valent Iron@Biochar (m/nZVI@BC) based SPC-RA system. Carrier size-fractionated m/nZVI@BC was fabricated by one-step carbothermal method. As a result, RA synergistically interacted with SPC, and the reaction time reduced from 15 min to 4 min. In the 0.010 g m/nZVI@BC-mediated SPC-RA system, over 95% of RhB (100 mg·L−1, 1041.667 mg·g−1) was successfully degraded. The maximum degradation ability could still exceed 1g·g−1 via 5 times repeated applications. Meanwhile, the loss of degradability, caused by halving SPC concentration could be compensated by RA dosage measurement. The entire degradation process was predominantly dominated by free radicals (•OH> 1O2> •O2−> •CO3−). Reactive oxidizing species (ROSs) were primarily excited by α-Fe0, Fe3C and N sites of biochar (BC). Light and BC carrier dedicated slight influence. These discoveries shed a light on the activity and recyclability regulation of catalytic material, aligning with the principles of green chemistry and cleaner production. This study demonstrates a novel approach to efficient management of solid waste disposal, reuse of waste biomass, advanced treatment of dye-containing wastewater, pollution control in aquatic environments.

Highly efficient peroxymonosulfate activation by CoFe2O4@attapulgite–biochar composites: Degradation properties and mechanism insights

Sulfate radical-based advanced oxidation processes (SR-AOPs) have been considered as a promising approach for degrading organic pollutants. Herein, CoFe2O4 anchored on attapulgite-biochar composites (CoFe2O4@ATP–BC) were synthesized by a sol-gel co-pyrolysis method and showed excellent catalytic performance, reusability and stability in activating peroxymonosulfate (PMS) for the degradation of Rhodamine B (RhB). The effects of PMS concentration, catalyst dosage, temperature, initial pH, NOM and inorganic ions on the removal of RhB were investigated. The radical quenching experiments and electron paramagnetic resonance (EPR) measurement confirmed that 1O2, O2∙− and surface-bound ∙OH and SO4∙− were major reactive oxygen species (ROS) in the RhB degradation by CoFe2O4@ATP–BC/PMS system, indicating that radical and non-radical degradation pathways were both involved. The possible catalytic mechanism of PMS by CoFe2O4@ATP–BC was proposed including the interface reaction and bulk reaction. The main degradation intermediates were identified by liquid chromatograph-mass spectrometry (LC-MS), and three possible degradation pathways of RhB were deduced accordingly. In general, the CoFe2O4@ATP–BC/PMS system provided fundamentals of theoretical and applied research to further develop supported bimetallic oxides for advanced oxidation treatment of organic wastewater.

A review on ZnO and its modifications for photocatalytic degradation of prominent textile effluents: Synthesis, mechanisms, and future directions

Effective and eco-friendly approaches are essential for dealing with organic pollutants in industrial waste. Textile dyes are toxic and carcinogenic, and releasing them into the environment leads to water pollution, posing significant health risks to all living beings and endangering aquatic life. The use of semiconducting metal oxides for photocatalytic pollutant degradation has emerged as an advanced wastewater treatment strategy. The multifunctional nature of ZnO, stemming from its affordability, environmentally friendly characteristics, structure-dependent properties, and ability to fully mineralize pollutants, positions it as a superior photocatalyst compared to other materials. However, its primary drawback is poor performance in visible light. This review delves into various synthesis techniques and their effects on morphology, structure, and band gap, and its subsequent influence on the photocatalytic performance. The review highlights the effect of doping ZnO with various alkaline earth metals, transition metals, noble metals, rare earth metals, and non-metals, along with studies reported on ZnO-metal oxide nanocomposites for photocatalytic dye degradation, by providing insights into the photodegradation mechanism involved. Furthermore, this review extensively investigates the strategies to improve ZnO's efficiency in degrading textile dyes, namely cationic and anionic dyes, under visible light conditions. For thorough understanding, the influence of various operational parameters such as catalyst loading, irradiation source, dye concentration, reaction time, and reaction kinetics on photocatalytic efficiency have been investigated in detail. The review also addresses existing challenges and potential future directions, providing some insights for possible development in this field.

Cobalt single-atom catalyst tailored ceramic membrane for selective removal of emerging organic contaminants

Water reuse is an effective way to solve the issues of current wastewater increments and water resource scarcity. Ultrafiltration, a promising method for water reuse, has the characteristics of low energy consumption, easy operation, and high adaptability to coupling with other water treatment processes. However, emerging organic contaminants (EOCs) in municipal wastewater cannot be effectively intercepted by ultrafiltration, which poses significant challenges to the effluent quality and sustainability of ultrafiltration process. Here, we develop a cobalt single-atom catalyst-tailored ceramic membrane (Co1-NCNT-CM) in conjunction with an activated peroxymonosulfate (PMS) system, achieving excellent EOCs degradation and anti-fouling performance. An interfacial reaction mechanism effectively mitigates membrane fouling through a repulsive interaction with natural organic matter. The generation of singlet oxygen at the Co-N3-C active sites through a catalytic pathway (PMS→PMS∗→OH∗→O∗→OO∗→1O2) exhibits selective oxidation of phenols and sulfonamides, achieving >90% removal rates. Our findings elucidate a multi-layered functional architecture within the Co1-NCNT-CM/PMS system, responsible for its superior performance in organic decontamination and membrane maintenance during secondary effluent treatment. It highlights the power of integrating Co1-NCNT-CM/PMS systems in advanced wastewater treatment frameworks, specifically for targeted EOCs removal, heralding a new direction for sustainable water management.

Performance of a Solar-Driven Photocatalytic Membrane Reactor for Municipal Wastewater Treatment

The increasing demand for efficient wastewater treatment technologies, driven by global population growth and industrialisation, highlights the necessity for advanced, reliable solutions. This study investigated the efficacy of a slurry photocatalytic membrane reactor (PMR) for the advanced removal of organic pollutants, quantified via chemical oxygen demand (COD), under natural and simulated solar light irradiation. Employing two variants of iron-doped titania as photocatalysts and a polysulfone-based polymeric membrane for the separation process, the investigation showcased COD removal efficiencies ranging from 66–85% under simulated solar light to 52–81% under natural sunlight over a 7 h irradiation period. The overall PMR system demonstrated COD removal efficiencies of 84–95%. The results confirmed the enhanced photocatalytic activity afforded by iron doping and establish solar-powered slurry PMRs as an effective, low-energy, and environmentally friendly alternative for the advanced treatment of municipal wastewater, with the research providing valuable insights into sustainable water management practices.

Evaluating the environmental and economic performance of biological and advanced biological wastewater treatment plants by life cycle assessment and life cycle costing.

The primary objective of this study is to assess and establish benchmarks for environmental and economic sustainability of biological and advanced biological wastewater treatment plants (WWTPs) with different treatment technologies and characteristics. Furthermore, the study aims to determine the beneficial role of WWTPs to reduction of eutrophication potential. Environmental and economic sustainability of ten municipal WWTPs was assessed using life cycle assessment (LCA) and life cycle costing (LCC). In the first section of the study, LCA was performed to determine the environmental performance of the WWTPs. Furthermore, net environmental benefit (NEB) approach was implemented to reveal the beneficial role of WWTPs to eutrophication potential. In the subsequent section, LCA-based LCC was conducted by integrating the results of LCA. The most significant environmental impact was determined as marine aquatic ecotoxicity, which is highly affected from the generation and transmission of electricity consumed in the WWTPs. Wastewater recovery and co-incineration of sewage sludge in cement kiln ensure significant environmental savings on ozone layer depletion, human toxicity, acidification, photochemical oxidation, and abiotic depletion (fossil fuel) potential. Considering NEB approach, the highest NEB values were found for the WWTPs with the higher organic load and nutrient concentration in the influent. The results of LCC in WWTPs varied between 0.21 and 0.53 €/m3. External (environmental) costs were evaluated higher than internal (operational) costs for all selected WWTPs. While eutrophication was the highest among environmental costs, electricity cost was the highest among operational costs for almost all WWTPs.

Study on the mechanism of mitigating membrane fouling in MFC-AnMBR coupling system treating sodium and magnesium ion-containing wastewater

ABSTRACT Anaerobic Membrane Bioreactors (AnMBR) offer numerous advantages in wastewater treatment, yet they are prone to membrane fouling after extended operation, impeding their long-term efficiency and stability. In this study, a coupled system was developed using modified conductive membranes as the filtration membrane for the AnMBR and as the anodic conductive membrane in the microbial electrochemical system, with a total volume of approximately 2.57 L. The research focused on understanding the membrane fouling characteristics of the AnMBR when treating wastewater containing sodium ion (Na+) and magnesium ion (Mg2+). When the system was treating wastewater containing Na+, organic pollutants such as proteins and polysaccharides were identified as the primary causes of membrane fouling. Three experimental groups generating different electric currents exhibited extended operational times compared to the open-circuit control group, with extensions of 30, 24, and 15 days, respectively. Conversely, when treating wastewater with Mg2+, organic–inorganic composite fouling, primarily driven by Mg2+ bridging, emerged as the key challenge, with the experimental groups showing operational extensions of 5, 8, and 23 days, respectively, in comparison to the control group. Analysis of proteins and polysaccharides indicated that electric current played a crucial role in reducing organic fouling in the sludge cake layer. When treating wastewater containing Na+, the effectiveness of membrane fouling control was directly proportional to the electric current, while when treating wastewater containing Mg2+, it was directly proportional to the voltage.

Research on the Properties of Wasteforms after Direct Involvement of Uranium-Containing Silica Gel in Glass Network Formation.

Uranium-containing silica gel (UCSG) is a secondary waste generated during the advanced treatment of nuclear wastewater. In order to reduce the growing storage pressure for UCSG, from the perspective of building a borosilicate glass network, UCSG was used to replace SiO2 in the glass-cured formula to directly achieve the immobilization of UCSG. SEM-EDS results showed that uranium was uniformly distributed in the matrix, and the maximum solid solubility of UCSG (two components: silica gel and uranyl ions) in the formula was as high as 55 wt %. At the same time, TG-MS proved that silica gel lost OH groups (down about 4.61 wt %) and formed Si-O-Si bond by condensation. FT-IR and XPS proved a change in the number of Si-O-Si bond, and new Si-O-B and Si-O-Al bond appeared on the spectrum. This was evidence that silica gel could self-involved participate in the construction of glass networks. EPR analysis obtained the changes in the coordination environment of U atom, the U atom decreased spin electrons number in the glass than in uranyl crystals. The glass also has good physical properties (hardness: 6.51 ± 0.23 GPa; density: 2.3977 ± 0.0056 g/cm3) and chemical durability (normalized leaching rate: LRU = 2.34 × 10-4 ± 2.05 × 10-6 g·m2·days-1 after 42 days), this research provided tactics for simple treatment of uranium-containing silica gel in one step.

Biosynthesized CS-MgO/zeolite hybrid material: An efficient adsorbent for chlorpyrifos removal - Kinetic studies and response surface methodology

The prevalence of organophosphate pesticides in aquatic environments raises severe concerns on a global scale. Chlorpyrifos, an insecticide, is included in a class of organophosphate pesticides. It is widely used on agricultural lands to control pests in cotton, fruit, and vegetables. The acute toxicity of chlorpyrifos is still dangerous to all aquatic living organisms. Then the treatment of water contaminated with chlorpyrifos is an important aspect. The recent decade has witnessed adsorption technology emerging as an advanced organophosphate pesticide wastewater treatment with great potential and a grand blueprint, in which the specific surface area and active sites of the adsorbent are considered to be the two most important characteristics largely impacting the adsorption performance. In this study, a CS-MgO/Zeolite composite was prepared by the microbial method as an effective adsorbent for the removal of chlorpyrifos from an aqueous solution. The adsorbent's properties were carefully characterized using X-ray diffraction, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The refinement of experimental conditions, encompassing variations in adsorbent dosage, contact time, and chlorpyrifos concentration at five discrete levels, was systematically undertaken through the utilization of a composite central design rooted in response surface methodology. The solution pH played a key role in chlorpyrifos removal, and a pH of 7.0 was selected according to its high adsorption ability. The highest removal (80.9%) of chlorpyrifos by CS-MgO/Zeolite was obtained at an optimum pH of 7, a contact time of 40 min, an adsorbent dosage of 0.4 g/L, and a chlorpyrifos concentration of 5 mg/L−1. The adsorption results were highly fitted with the Freundlich adsorption isotherm model, and the maximum adsorption was 83.3 mg/g. Kinetic studies indicate that the removal of chlorpyrifos followed the pseudo-second-order model of adsorption (0.994). The thermodynamic parameters indicate the spontaneous and endothermic nature of chlorpyrifos sorption on CS-MgO/Zeolite sorbent. The results revealed that introducing chitosan could improve the adsorption capacity and rate effectively even though it sacrificed part of the specific surface areas of the MgO/Zeolite, indicating that active sites might play a dominant role during chlorpyrifos adsorption. The fabricated CS-MgO/Zeolite adsorbent nanocomposite displayed high reusability based on the elution and simultaneous regeneration ability. Therefore, as a cheap green nanocomposite adsorbent with high adsorption performance for chlorpyrifos, the CS-MgO/Zeolite nanocomposite adsorbent is expected to become one of the best candidate materials for chlorpyrifos removal aqueous solutions.

Assessment of Energy Self-Sufficiency of Wastewater Treatment Plants—A Case Study from Poland

Currently, one of the main goals is to make municipal wastewater treatment plants (WWTPs) energy-neutral. However, advanced wastewater treatments and sewage sludge processing are still classified as highly energy-intensive. In this study, the energy self-sufficiency potential assessment of the WWTP located in Krosno (Poland) was evaluated. Moreover, the possible paths for improving the energy balance of the analyzed facility are presented in this paper. The performed evaluation indicated that in 2016–2019, the energy consumption at WWTP Krosno varied from 0.25 to 0.71 kWh/m3 of wastewater (average 0.51 kWh/m3), and the highest energy utilization values in each year were recorded around the summer season. An analysis of the data showed that as the pollutant load flowing into the WWTP increased, its energy utilization decreased. Such results indicate that the treatment cost per cubic meter decreases as the load increases due to the capital cost being the same. The estimated self-sufficiency of the facility in the years analyzed was 50.5%. The average energy recovery from 1 m3 of wastewater was 0.27 kWh/m3, and the average energy recovery from 1 m3 of biogas was 1.54 kWh/m3. Since the energy balance of this wastewater treatment plant, determined primarily by the continuously increasing cost of energy purchases, has to be improved, two courses of action were identified that will allow for increasing self-sufficiency. The co-digestion strategy was indicated as the easiest solution to implement, given the on-going anaerobic stabilization of sewage sludge at this WWTP. Moreover, the possible co-substrates that can be obtained from local suppliers were indicated. The second course of action, which requires a thorough economic analysis, is sludge pre-treatment, which might improve sewage sludge properties, resulting in a more favorable biogas yield.

Recent advances of membrane-based hybrid membrane bioreactors for wastewater reclamation

Membrane bioreactor (MBR) is an advanced wastewater treatment technology, which has been established for more than 3 decades. In MBRs, membrane separation allows not only rejecting microorganisms/greater-sized molecules but decoupling hydraulic retention time (HRT) and solid retention time (SRT). Low-pressure driven, porous membranes have been widely used in MBRs, but their performances are mainly limited for wastewater reuse applications. Recently, many attempts have been made to combine desalination technologies to advance hybrid MBR processes for wastewater reclamation. Nanofiltration (NF) and reverse osmosis (RO) have been applied with the MBRs to improve effluent quality, and their advantages and challenges have been well reported in terms of rejection efficiency, operational energy, fouling control and recovery of retentate stream. Alternatively, the direct introduction of non-pressurized desalination technologies such as forward osmosis (FO) and membrane distillation (MD) into MBR processes for wastewater reclamation or probably for microbial activity have been considered substantially due to their low energy consumption and excellent rejection efficiency of solid materials. However, several technical limitations still need to be resolved to commercialize hybrid FO- or MD-MBR processes. This paper reviews recent advances of MBR technology integrated with desalination technologies for wastewater reclamation and suggests perspectives to optimize membrane-based hybrid MBR process.

Enhanced coking wastewater advanced treatment by using particle electrodes excited persulfate in the three-dimensional electrocatalytic reactors

Problems such as low concentration of organic pollutants in the biochemical effluent of coking wastewater and poor mass transfer efficiency have seriously affected the effectiveness of coking wastewater depth. Three-dimensional electrode oxidation processes (3DEOPs) are a very promising advanced oxidation process for wastewater treatment. Compared with the 3DEOPs, the treatment effect of coking wastewater was greatly improved by adding persulfate (PS) into the 3DEOPs. The experimental results showed that under the condition of adjusting the current density of 32 mA/cm2, adding 35 g of TSC6/BC particle electrodes and 2 mM PS, the COD concentration of the coking wastewater was reduced from 245.40 mg/L to 71.00 mg/L after 40 min of electrolysis, which has already met the discharge requirements. After 120 min of electrolysis, the UV254 of coking wastewater was reduced from 2.46 cm−1 to 0.35 cm−1, and the removal rate of COD and TOC in coking wastewater reached 93.44% and 78.19%, respectively. Compared with the use of BC and TiO2/BC, TS9/BC particle electrodes，the time for coking wastewater to meet the discharge standard was shortened by 20–30 min with TSC6/BC particle electrodes. Furthermore, the TSC6/BC particle electrodes improves the current efficiency and also saves energy of the system. The experimental results showed that both SO4−· and ·OH radicals in the 3DEOPs excited PS system play a very important roles to the degradation of organic pollutants in coking wastewater. This study provides theoretical guidance and technical support for the application of three-dimensional electrocatalytic technology for the treatment of actual coking wastewater.

Enhancement of denitrification by sulfur-based carrier in sequencing batch reactor (SBR) for advanced wastewater treatment

This study was to enhance the nitrogen removal efficiency in the sequencing batch reactor (SBR) process by adding sulfur-based carriers. The nitrogen removal efficiency of the control group was compared with that of the experimental group through a two-series operation of SBR1 without carrier and SBR2 with the carrier under the condition of no external carbon source. A total nitrogen (T-N) removal efficiency of 6.6%, 72.6%, and 79.9% was observed in SBR1, SBR2 (5%), and (10%), respectively. The T-N removal efficiency was improved in the system with carriers, which showed an increase in the removal efficiency of approximately 91.7%. The results suggest that the inclusion of the carrier led to an elevation in the sulfur ratio, implying an augmented surface area for sulfur-based denitrifying microorganisms. Additionally, CaCO3 contributed essential alkalinity for sulfur denitrification, thereby preventing a decline in pH. Regardless of the carrier, the efficiency of organic matter removal surpassed 89%, indicating that the sulfur-based carrier did not adversely affect the biological reaction associated with organic matter. Therefore, autotrophic denitrification was successfully performed using a sulfur carrier in the SBR process without an external carbon source, improving the nitrogen removal efficiency.

Nanoarchitectonics Design Strategy of Metal-Organic Framework and Bio-Metal-Organic Framework Composites for Advanced Wastewater Treatment through Adsorption.

Freshwater depletion is an alarm for finding an eco-friendly solution to treat wastewater for drinking and domestic applications. Though several methods like chlorination, filtration, and coagulation-sedimentation are conventionally employed for water treatment, these methods need to be improved as they are not environmentally friendly, rely on chemicals, and are ineffective for all kinds of pollutants. These problems can be addressed by employing an alternative solution that is effective for efficient water treatment and favors commercial aspects. Metal organic frameworks (MOFs), an emerging porous material, possess high stability, pore size tunability, greater surface area, and active sites. These MOFs can be tailored; thus, they can be customized according to the target pollutant. Hence, MOFs can be employed as adsorbents that effectively target different pollutants. Bio-MOFs are a kind of MOFs that are incorporated with biomolecules, which also possess properties of MOFs and are used as a nontoxic adsorbent. In this review, we elaborate on the interaction between MOFs and target pollutants, the role of linkers in the adsorption of contaminants, tailoring strategy that can be employed on MOFs and Bio-MOFs to target specific pollutants, and we also highlight the effect of environmental matrices on adsorption of pollutants by MOFs.